« previous next »
Pages: [1] 2

Author Topic: Too short Osage  (Read 6292 times)

0 Members and 1 Guest are viewing this topic.

roofus

  • Guest
Too short Osage
« on: October 07, 2009, 12:20:43 pm »
I can get a couple of good chunks of Osage for pretty cheap. These are very straight grained demensional boards. Not staves.
They are right at 3' long each. Do you think I can joint them in the middle an glue on a handle riser and back it with Hickory and end up with a good bow?

Rob
Logged

Offline RyanY

  • Member
  • Posts: 1,999
Re: Too short Osage
« Reply #1 on: October 07, 2009, 12:32:25 pm »
Yes.
Logged

roofus

  • Guest
Re: Too short Osage
« Reply #2 on: October 07, 2009, 12:33:36 pm »
Easy enough. I'll let you know how it turns out.

Rob
Logged

Offline RyanY

  • Member
  • Posts: 1,999
Re: Too short Osage
« Reply #3 on: October 07, 2009, 12:46:58 pm »
I saw a piece of osage at the lumber mill that I go to and thought the same thing. I didn't do it though because I have no experience in splicing. Good luck.
Logged

roofus

  • Guest
Re: Too short Osage
« Reply #4 on: October 07, 2009, 12:49:49 pm »
Splicing is no biggie. PM me and I'll send you a link. I think I can do that right?
Logged

roofus

  • Guest
Re: Too short Osage
« Reply #5 on: October 07, 2009, 12:58:59 pm »
Here is that link. If this is wrong to do please let me know.

http://www.auf.asn.au/scratchbuilder/joints.html#joints

Rob
Logged

roofus

  • Guest
Re: Too short Osage
« Reply #6 on: October 08, 2009, 01:39:46 am »
I got two nice chunks the shortest being 36" the longer over 45". I gave $9 for the 45" and $7 for the 36" both 3/4
I was able to saw two 2" wide pieces out of the 36" piece. I spliced them and glued up the riser. osage/walnut/cedar/walnut/maple.
I'll post some pics if you're interested. After the glue dries.
Logged

Offline zeNBowyer

  • Member
  • Posts: 649
Re: Too short Osage
« Reply #7 on: October 08, 2009, 01:50:15 am »
Sounds  like  a  2-piece TD  bow  to  me:)
Logged
"There's  something  immoral  about  abandoning  your  own  judgement"
Cowards always run in  packs
Ishi did not become the arrow, I suspect. The arrow became Ishi.

roofus

  • Guest
Re: Too short Osage
« Reply #8 on: October 08, 2009, 06:24:03 pm »
Yup. Minus the take down part.
Logged

Offline Justin Snyder

  • Administrator
  • Member
  • Posts: 13,794
Re: Too short Osage
« Reply #9 on: October 08, 2009, 07:20:45 pm »
Sounds like you got it figured out.
Logged
Everything happens for a reason, sometimes the reason is you made a bad decision.


SW Utah

roofus

  • Guest
Re: Too short Osage
« Reply #10 on: October 08, 2009, 10:22:45 pm »
I don't know about that. But I have a plan. I'll document the process so if it is a success I can repeat it and share it.
I appreciate everyone's input and advise! This site rules ;D

Rob
Logged

Shadow Walker

  • Guest
Re: Too short Osage
« Reply #11 on: October 11, 2009, 07:07:09 pm »
the april/may 2009 edition of PA has an article on splicing that is quite informative.Page 30. It shows different methods for splicing at the handle fort maximum strenght.
Logged

roofus

  • Guest
Re: Too short Osage
« Reply #12 on: October 11, 2009, 10:29:06 pm »
Thanks. I have already made the splice. I did the v cut method. It is a very strong joint along with the handle riser glued up. I don't anticipate any issues.
I did run into a tiny little knot, but I don't think it goes very deep.
I'll be posting some pics soon. Thanks again, I really appreciate the help!!!!!!!

Rob
Logged

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Too short Osage
« Reply #13 on: October 12, 2009, 10:02:36 am »
Don't think a V cut is the proper splice for a bow, you need a fish tail or a Z splice. The easiest way is to draw the splice on a piece of paper, cut the pattern out and glue it on your wood with Elmer's glue. Line the pattern up with a center line on your bow and cut your splice.

In the picture I am adding a new limb to the good half of a broken bow.

Logged

Offline Dano

  • Member
  • Posts: 1,349
Re: Too short Osage
« Reply #14 on: October 12, 2009, 11:47:58 am »
The V or W splice is a good splice, just have to makes sure the fingers aren't too wide. The less end grain the better.
Logged
"If the women don't find you handsome, they should at least find you handy."


Nevada
Pages: [1] 2
« previous next »