Author Topic: Show me your arrow tools!!!! (Read 16611 times)

GregB · « **Reply #15 on:** July 09, 2008, 08:47:11 am »

Pappy has one like Sawfiler uses, except I think he purchased it.

Has anyone else noticed that if reheating nodes more then once they're not as readily plyable as the first time? I might have been getting mine to hot.

Pappy · « **Reply #16 on:** July 09, 2008, 08:51:27 am »

I have one of them,didn't make it ,I got it from Ace,I have been using it on my Cain arrows to compress the nodes.It works great for that.Heat them up and roll the flat.I also used it on some Hickory shafts.I just heated the area and rolled them on the high side and worked great also.
Pappy

JackCrafty · « **Reply #17 on:** July 09, 2008, 02:31:08 pm »

Great ideas here....

There's a well-known video on youtube that briefly shows a slick arrow straightening tool used by a master arrow-maker. I saw it a while ago, but it didn't dawn on me, until recently, that I missed it. I watched it again, copied the tool (made it out of mulberry branch), and it works great.

Here's the link:
http://www.youtube.com/watch?v=93EoM77bCVc&feature=related

The arrow straightening tool appears at 1:36, good closeup at 1:48, and appears again at 5:05.

El Destructo · « **Reply #18 on:** July 09, 2008, 07:37:12 pm »

Nice tool......and try to do that little Stunt at the End with a POC Arrow ....or a Hardwood for that matter!!!!

Butch Speer · « **Reply #19 on:** July 10, 2008, 09:20:36 pm »

D Tiller,
Sorry it took a while to get back. Those are 2x2s about 6ins. long. Set apart just enough to allow for the arrow. Mounted on a piece of plywood with another 2x2 on the bottom so you can chuck it in a vise.

Butch

D. Tiller · « **Reply #20 on:** July 10, 2008, 10:02:13 pm »

THANKS!

Pappy · « **Reply #21 on:** July 14, 2008, 06:19:04 am »

Here are some of mine, Finely got some pictures.Keep in mind you don't need all this stuff
I am just a tool and equipment nut.I like stuff.

Pappy

[attachment deleted by admin]

Pappy · « **Reply #22 on:** July 14, 2008, 06:24:53 am »

The first are arrow straighting tools,Grain scale,spine tester,cresting tool,Tapering jig,Cut off tool,another spin tester,feather splitter,Camp stove and I also have a wood chuck to taper nock and point ends if I don't do self nocks.

Pappy

[attachment deleted by admin]

DBernier · « **Reply #23 on:** July 14, 2008, 07:31:09 am »

Pappy, nice "stuff" The only thing I can add is on your arrow tapering tool is to drill a series of 1/4 inch dia. holes down between the angles to let a lot of the dust filter down out of the way. Helps in not clogging the sandpaper/files etc. Again, nice "stuff".

Dick

Phillip K · « **Reply #24 on:** July 14, 2008, 01:53:19 pm »

Pretty Impressive implements, I just used these and some of that fat mixture before I Burnish the Arrow after Fletching.I used a bent Butter knife and heat it to shape the Fletches.PK Good Day

JackCrafty · « **Reply #25 on:** August 05, 2008, 09:57:09 pm »

Recently I was asked to send pictures of the tools I use to straighten arrow shoots. Well, I'm going to post them here in case others might be interested. Sorry for the poor quality of the close-ups. (Hopefully, I will be getting a better camera soon

).

[attachment deleted by admin]

Pappy · « **Reply #26 on:** August 06, 2008, 05:34:33 am »

Very cool,I'll have to make me one of those.

Pappy

DBernier · « **Reply #27 on:** August 06, 2008, 07:07:00 am »

Very functional and the best part

Simple.

Dick

stringstretcher · « **Reply #28 on:** August 11, 2008, 06:41:42 pm »

Just curious if anyone watche the video posted above, does anyone know where to get the plans to build a stove/oven like they use with compressed charcoal?

NorthernArcher · « **Reply #29 on:** September 09, 2008, 11:32:51 pm »

Here's what I have been using...

i

Primitive Archer