« previous next »
Pages: [1] 2

Author Topic: trade point pointers  (Read 4552 times)

0 Members and 1 Guest are viewing this topic.

Offline GaryR

  • Member
  • Posts: 200
trade point pointers
« on: November 02, 2011, 03:28:01 pm »
Trade point thickness. I read that soup can lids can be used, I've made a couple but they seem too flimsy. I have a discarded mitre saw blade I was thinking of using, but I think its a bit thick. Is their a standard?
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: trade point pointers
« Reply #1 on: November 02, 2011, 05:54:02 pm »
Around .050" more or less. Generally circular saw blades work well.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline ken75

  • Member
  • Posts: 1,886
  • crepe myrtle is my "yella wood"
Re: trade point pointers
« Reply #2 on: November 02, 2011, 06:29:55 pm »
what pat said , that and old band saw blades ive got a bunch of 050 thats good and some 080 thats tough as nails.
pat did you try the 080 yet ?
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: trade point pointers
« Reply #3 on: November 02, 2011, 10:00:17 pm »
Not yet, Ken. Haven't had time. Winter project!  ;)
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline gstoneberg

  • Member
  • Posts: 3,889
Re: trade point pointers
« Reply #4 on: November 03, 2011, 01:10:59 am »
Gary, I can cut you a strip off the band saw blade I have if you want.  I also have a couple flint points you can have.

George
Logged
St Paul, TX

Offline bowtarist

  • Member
  • Posts: 3,503
  • Primitive Archer Subscription Number PM103651
Re: trade point pointers
« Reply #5 on: November 03, 2011, 01:50:01 am »
Quote from: ken75 on November 02, 2011, 06:29:55 pm
what pat said , that and old band saw blades ive got a bunch of 050 thats good and some 080 thats tough as nails.

I use circ. blades for big game points, single beveled and bandsaw blades for small game if I need more than a blunt.  You can get into a circ. blade unbelievably quick w/ a good cold chiesel and a good solid hammering surface.  Cut em big and grind or/and file.  It's up to you on the bevel and the edge, people do it different ways, but they all seem to work well enough if the shot is in the vitals.  ;)  good luck and post pics!
Logged
(:::.)    Osage music played daily. :)

Offline GaryR

  • Member
  • Posts: 200
Re: trade point pointers
« Reply #6 on: November 03, 2011, 12:39:17 pm »
George, I'll take a piece of bandsaw blade and flints when we get together next, Thanx.
Logged

Offline GaryR

  • Member
  • Posts: 200
Re: trade point pointers
« Reply #7 on: November 03, 2011, 12:55:33 pm »
I guess I'm just wasting time with the soup can lids then?
Logged

Offline Dazv

  • Member
  • Posts: 472
Re: trade point pointers
« Reply #8 on: November 03, 2011, 01:27:38 pm »
soup can lids would be far to thin i think i would just bend on contact.
Logged

Offline GaryR

  • Member
  • Posts: 200
Re: trade point pointers
« Reply #9 on: November 03, 2011, 01:31:25 pm »
Thanx guys, I'm now educated.
Logged

Offline Prarie Bowyer

  • Member
  • Posts: 1,599
Re: trade point pointers
« Reply #10 on: November 04, 2011, 02:53:31 am »
That metal that is used on band straps on pallets is also good if you can get it wide enough.

Logged

Offline crooketarrow

  • Member
  • Posts: 2,790
Re: trade point pointers
« Reply #11 on: November 06, 2011, 08:31:59 am »
  I like  to use old saw mill blades same as I use for knives it's 1/8 inch you can sand them down to a razor edge retemper them There perfect 1/2 inch is the same thickest as 3 hack saw blades and leaves plenty or shafe it there 3/8's or larger. For safting them on. Or you can sand the end down if you have smaller size shafes I like the 3 to 1 ratio but I like mine 2 3/4's. At 1/8" and tempered you never have the tip roll up even on cinder blocks. I've thyed.
Logged
DEAD IS DEAD NO MATTER HOW FAST YOUR ARROW GETS THERE
20 YEARS OF DOING 20 YEARS OF LEARNING 20 YEARS OF TEACHING

Offline IsaacW

  • Member
  • Posts: 182
Re: trade point pointers
« Reply #12 on: November 07, 2011, 12:53:13 pm »
What do you all use to cut them out?

Logged
We shall never achieve harmony with land, any more than we shall achieve absolute justice or liberty for people. In these higher aspirations, the important thing is not to achieve but to strive.
Aldo Leopold

Offline beetlebailey1977

  • Member
  • Posts: 1,153
    • Bowhunters of South Carolina
Re: trade point pointers
« Reply #13 on: November 07, 2011, 10:45:40 pm »
I have two that I am making now out of a broken High Speed Steel slitting saw blade......they are very hard and .080" thick.  I will post some pics when I get a chance.
Logged
Happy hunting to all!
Bowhunters of South Carolina Executive council member
Professional Bowhunters Society Associate member

Reevesville, SC     James V. Bailey II

Offline Bill Skinner

  • Member
  • Posts: 384
Re: trade point pointers
« Reply #14 on: November 09, 2011, 01:04:35 am »
I have cut saw blades with a side grinder.  Use the cutting blade, the grinding blade makes too wide a cut and you waste a lot of metal and grinding blade.
Logged
Pages: [1] 2
« previous next »