« previous next »
Pages: 1 [2]

Author Topic: Pucker time.  (Read 11389 times)

0 Members and 1 Guest are viewing this topic.

Offline Justin Snyder

  • Administrator
  • Member
  • Posts: 13,794
Re: Pucker time.
« Reply #15 on: January 05, 2009, 01:18:46 am »
I'm glad I'm not the only one that waits until I'm done to break my points or knives.  Good looking work.  Justin
Logged
Everything happens for a reason, sometimes the reason is you made a bad decision.


SW Utah

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,911
  • Eddie Parker
Re: Pucker time.
« Reply #16 on: January 05, 2009, 09:46:14 pm »
 Thanks Justin.
Logged
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline leapingbare

  • Member
  • Posts: 2,028
    • http://www.flintknappers.com/jessewright/
Re: Pucker time.
« Reply #17 on: January 06, 2009, 11:26:43 am »
Nice Save Eddie..
 I dont have a problem fllooting.. i just dont know how to run the floot to the tip of the point without end snapping it.. like Folsom and comberlands.
Logged
Mililani Hawaii

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,911
  • Eddie Parker
Re: Pucker time.
« Reply #18 on: January 06, 2009, 01:10:31 pm »
 I've watched Claude do it a couple of ways. He always leaves the point flat and sets it up in are carved out wooded platform. He then prepares and strikes the nipple as most people do. the other way is to use a little pressure vice, forgot the name, but it's like a little lever and you just keep applying pressure until it pops.
Logged
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline leapingbare

  • Member
  • Posts: 2,028
    • http://www.flintknappers.com/jessewright/
Re: Pucker time.
« Reply #19 on: January 06, 2009, 03:37:33 pm »
I have seen the vice.. but it dose not leave a floot flake scare thats typical of a original point.

 I do have one idea.. i could make a preform 3'' longer then i need it.. so lets say 6'' total.. than knock off one good float over 1/2 down the point. than knock the 2nd float off hard enough to end snap it. take my pressure flaker and touch it up.. and wala got a 3'' Folsom.. thats the plan. i dont have a pice of rock large enough over here so I'll have to wait till i get bake to try this.
Logged
Mililani Hawaii

Offline Hillbilly

  • Member
  • Posts: 8,248
  • I like tater tots.
Re: Pucker time.
« Reply #20 on: January 06, 2009, 04:01:39 pm »
Jesse, part of the thing I was talking about is to set the tip up on a bevel toward the side you're fluting. Then when you put the tip on a block of antler or hardwood and smack the nipple, it's almost like bipolar flaking. Most original Folsoms are a lot smaller than Clovis points-like 2-3" long.
Logged
Smoky Mountains, NC

NeolithicHillbilly@gmail.com

Progress might have been all right once but it's gone on for far too long.

Offline D. Tiller

  • Member
  • Posts: 3,507
  • Go ahead! Bend that stick! Make my day!!!
    • Whidbey Island Soap Co.
Re: Pucker time.
« Reply #21 on: January 06, 2009, 05:15:15 pm »
Hey Eddie, where ya get the obsidian? Looks really nice stuff.
Logged
“People are less likely to shoot at you if you smile at them” - Mad Jack Churchill

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,911
  • Eddie Parker
Re: Pucker time.
« Reply #22 on: January 06, 2009, 09:13:35 pm »
 Some came from Glass Buttes, compliments of Brian Melton. The other came from Justin, Utah. They are both good. I found the purple streaks in the stuff from Justin.
Logged
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline leapingbare

  • Member
  • Posts: 2,028
    • http://www.flintknappers.com/jessewright/
Re: Pucker time.
« Reply #23 on: January 06, 2009, 10:37:08 pm »
Hillbilly can you show me at the classic?
Logged
Mililani Hawaii

EndoftheWorldSurvivor

  • Guest
Re: Pucker time.
« Reply #24 on: January 07, 2009, 12:11:22 am »
has anyone made a primitive saw to split antler? any other primitive ways to split antler appreciated as well.
Logged

Offline Hillbilly

  • Member
  • Posts: 8,248
  • I like tater tots.
Re: Pucker time.
« Reply #25 on: January 07, 2009, 08:48:05 am »
Jesse, I'll try-I sure haven't mastered fluting folsoms yet, either. I can get a decent Clovis now and then, but I'm sure no expert on fluting. I'm positive I  can show you how to roll-fracture one into two pieces on the second flute. ;D I'm like you, jig fluting just don't do it for me-I like to try to figure out how to do it like they did it. EOTWS, the usual primitive method of splitting antler is to soak it until it gets soft, then score it with a burin flake and split it.
« Last Edit: January 07, 2009, 08:51:20 am by Hillbilly »
Logged
Smoky Mountains, NC

NeolithicHillbilly@gmail.com

Progress might have been all right once but it's gone on for far too long.

Offline cowboy

  • Member
  • Posts: 7,035
  • Paul Wolfe. Springtown, TX
Re: Pucker time.
« Reply #26 on: January 07, 2009, 09:13:50 am »
Nice job on the points Eddie. Too bad on the knife but nice save though, I'll have to get around to some fluting one of these days.
Logged
When you come upon a track or trail you do not know, follow it to the point of knowing.

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,911
  • Eddie Parker
Re: Pucker time.
« Reply #27 on: January 07, 2009, 04:03:27 pm »
  thanks Paul.
Logged
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

EndoftheWorldSurvivor

  • Guest
Re: Pucker time.
« Reply #28 on: January 07, 2009, 06:14:13 pm »
thanks hillbilly any more tips on knapping?
Logged
Pages: 1 [2]
« previous next »