« previous next »
Pages: [1]

Author Topic: Any experience on stripping tru oil ?  (Read 1958 times)

0 Members and 2 Guests are viewing this topic.

Offline bentstick54

  • Member
  • Posts: 770
Any experience on stripping tru oil ?
« on: May 08, 2017, 11:24:17 pm »
What would be the safest way to strip and refinish an Osage selfbow without taking the natural darkening of the wood out or change weight and tiller?
I originally put 5 or 6 coats of tru oil on, and then topped off with a light coat of satin spray poly to knock the shine. I have touched up a few scratches and knicks over the seasons, but would like to do a total refinish without losing the natural orange color of the aging wood?
Should I steel wool as much as I can till all scratches are removed,stopping short of actually getting to the wood itself, or should I take as much off with acetone or other stripper,then steel wool and refinish?
Again I don't want to lose draw weight or risk tiller.
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Any experience on stripping tru oil ?
« Reply #1 on: May 08, 2017, 11:43:45 pm »
A light scraping! If the scraping lightens the osage just lay it in bright sunlight and it will darken. The satin poly being harder than the Tru-Oil should come off with the Tru-Oil.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline bentstick54

  • Member
  • Posts: 770
Re: Any experience on stripping tru oil ?
« Reply #2 on: May 10, 2017, 06:22:44 pm »
Thx Pat, I knew that was an option but wasn't sure if there were any others. Bow is 5 years old and taken on a nice red/orange hue now and am hoping on not loosing it. I will probably try scraping gently and then steelwooling.
Logged

Offline jaxenro

  • Member
  • Posts: 247
Re: Any experience on stripping tru oil ?
« Reply #3 on: May 10, 2017, 09:02:47 pm »
I used citristrip on a truoil finished gunstock once seemed to work well

Not much for steel wool though I have seen bits get embedded in the wood
« Last Edit: May 11, 2017, 07:18:32 am by jaxenro »
Logged

Offline Hawkdancer

  • Member
  • Posts: 5,040
Re: Any experience on stripping tru oil ?
« Reply #4 on: May 10, 2017, 11:30:35 pm »
Bronze wool seems to work better than steel wool, doesn't leave shreds in the wood.  I have used it on gunstocks.
Hawkdancer
Logged
Life is far too serious to be taken that way!
Jerry

Offline Hrothgar

  • Member
  • Posts: 1,477
Re: Any experience on stripping tru oil ?
« Reply #5 on: May 11, 2017, 06:35:40 am »
A 600 grit sandpaper would also work, try O'Reillys or any automotive parts store.
Logged
" To be, or not to be"...decisions, decisions, decisions.

Offline bentstick54

  • Member
  • Posts: 770
Re: Any experience on stripping tru oil ?
« Reply #6 on: May 14, 2017, 10:09:30 pm »
I found a well used piece of 320grit sandpaper, so I gently sanded the finish down smooth. Luckily I did not have to sand down to raw wood. I then rubbed it down with 0000 steel wool, then wiped down with a tack cloth.
I was able to save the 5 years worth of darkening the bow had acquired, so was very happy with that.
I rubbed 3 new coats of Truoil on, and it came out looking pretty good. Just need to knock the shine down a little and I will be done. 
Logged
Pages: [1]
« previous next »