« previous next »
Pages: [1]

Author Topic: bord bow tiller check  (Read 1728 times)

0 Members and 1 Guest are viewing this topic.

Offline littlehunters19862011

  • Member
  • Posts: 183
bord bow tiller check
« on: November 02, 2016, 06:46:31 pm »
been working on this  Lil board  about two days . i thought i had it bending   evenly  but didn't have a tellering tree last night to check. and was hard to see  how it was bending.  made  a tellering tree today and got it on there . going to try and mack it with deer rawhid. if it gets that far .
Logged

Offline High-Desert

  • Member
  • Posts: 876
Re: bord bow tiller check
« Reply #1 on: November 02, 2016, 06:50:11 pm »
Do you have a profile pic?

Eric
Logged
Eric

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: bord bow tiller check
« Reply #2 on: November 02, 2016, 07:15:23 pm »
Your outer third on your left limb is stiff.Left limb is doing most of it's work midlimb.The right limb is bending pretty good.
Logged
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline littlehunters19862011

  • Member
  • Posts: 183
Re: bord bow tiller check
« Reply #3 on: November 02, 2016, 07:51:12 pm »
i haven't cut the tips down yet there still full width. and i thought  it was stuff on the fade area  a bet but it was hard to tell. i have not had any luck with making bows. just thought ID give it another try.
« Last Edit: November 02, 2016, 07:59:01 pm by littlehunters19862011 »
Logged

Offline Eric Krewson

  • Member
  • Posts: 5,436
Re: bord bow tiller check
« Reply #4 on: November 02, 2016, 07:54:12 pm »
Like a broken record I put forth the same thing, you need a tillering gizmo.
Logged

Offline SLIMBOB

  • Member
  • Posts: 3,759
  • Deplorable Slim
Re: bord bow tiller check
« Reply #5 on: November 02, 2016, 09:38:03 pm »
Your tiiller looks like you are going for a lever type bow.  No bend out board.  Your profile doesn't show that to be the case.  Finish the profile first, then work on getting the entire limb working.  Eric mentioned the Gizmo.  That or just a straight edge so that each section of the limb is doing it's share.  You will end up taking lots of set the way your going now.  Or a take down mid limb.
Logged
Liberty, In God We Trust, E Pluribus Unum.  Distinctly American Values.

Offline mikebarg

  • Member
  • Posts: 54
Re: bord bow tiller check
« Reply #6 on: November 03, 2016, 06:14:49 pm »
Keep going. Don't give up on it. You need to cut the taper in the limbs. Go look at the limb width taper and thickness taper of some of the bows on this site. That will give you an idea of what it needs to look like. Look at some board bow build along threads.
Logged

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: bord bow tiller check
« Reply #7 on: November 04, 2016, 08:50:57 am »
Yes width taper those limbs from midlimb on out will help with the bend on the outers a bit.
Logged
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline littlehunters19862011

  • Member
  • Posts: 183
Re: bord bow tiller check
« Reply #8 on: November 04, 2016, 03:42:12 pm »
thanks for the encouragement every one .  i done  a Lil more tillering on that limb last night. took little off at a time its batter now then it was
Logged
Pages: [1]
« previous next »