« previous next »
Pages: [1]

Author Topic: tiller help  (Read 1709 times)

0 Members and 2 Guests are viewing this topic.

Offline helmet

  • Member
  • Posts: 168
tiller help
« on: October 08, 2016, 06:21:26 pm »
I am stuggling with this one. Its white oak, I am currently at 40lbs @21". I would like to get 50lbs @ 26". The set is about a 1/4" right now, but I dont feel confident in the tiller. Any help is appreciated.
Logged

Offline Dictionary

  • Member
  • Posts: 717
Re: tiller help
« Reply #1 on: October 08, 2016, 06:30:09 pm »
I think you need to get the fades bending. it's maybe just a tad bit whipended
« Last Edit: October 08, 2016, 06:52:23 pm by Dictionary »
Logged
"I started developing an eye for those smooth curves as a young man.  Now that my hair is greying and my middle spreading I make bows instead."

-JW_Halverson

Offline bjrogg

  • Member
  • Posts: 11,017
  • Cedar Pond
Re: tiller help
« Reply #2 on: October 08, 2016, 07:35:43 pm »
I thought the same as JW at 1st but it looks like your unbraced profile has a quite a bit reflect in the fades. Might not be to bad, hard for me to tell. I do agree with JW on out 1/3 wouldn't take anymore there. How close are you on draw and wieght? I'm no expert and the reflex in the handle might be throwing me for a loop. You might want to see what others say, but I think I'd take off from fades and mid limb.
Logged
A hot cup of coffee and a beautiful sunrise

Offline helmet

  • Member
  • Posts: 168
Re: tiller help
« Reply #3 on: October 08, 2016, 08:06:35 pm »
bjrogg , I would like to get 50lbs at 26" but I have only pulled  it to 40lbs at this point, and that took it out to 21". Do you guys think if I take some wood off the fades and midlimb that I would be safe to pull to 50lbs?
Logged

Offline Buckeye Guy

  • Member
  • Posts: 3,033
Re: tiller help
« Reply #4 on: October 08, 2016, 08:09:30 pm »
Go ahead and pull it to 50 see what it looks like
Logged
Guy Dasher
The Marshall Primitive Archery Rendezvous
Primitive Archery Society
Having  fun
To God be the glory !

Offline bentstick54

  • Member
  • Posts: 770
Re: tiller help
« Reply #5 on: October 08, 2016, 10:42:35 pm »
Looking at it on my I-phone so take with a grain of salt. Agree with leaving tips alone but almost looks like the start of a possible hinge right at the fade on the right side. Could be an optical illusion though. I agree with Buckeye, slowly exercise it up to 50# before removing any more and see what you have.
Logged

Offline Badger

  • Member
  • Posts: 8,124
Re: tiller help
« Reply #6 on: October 08, 2016, 11:01:18 pm »
  Reflexing right off the handle like that will sometimes give you a bow that starts to stack at full draw. I would slowly work it up to 50# as suggested monitoring the set as you go. I would take more out in the inner 1/3 limbs.
Logged

Offline helmet

  • Member
  • Posts: 168
Re: tiller help
« Reply #7 on: October 08, 2016, 11:33:36 pm »
Thank you for your replies folks, I will get it out to 50lb tommorrow and see what I have. After bentsick54's  reply, I see three possible hinges. The other two are out  towards the tips. I am a little nervous cause I have broke a few bows this year :-\
Logged

Offline helmet

  • Member
  • Posts: 168
Re: tiller help
« Reply #8 on: October 08, 2016, 11:38:01 pm »
Badger I see what you mean on reflexing the handle, that clears up the string angle issue I was seeing.
Logged

mikekeswick

  • Guest
Re: tiller help
« Reply #9 on: October 09, 2016, 04:17:57 am »
40 @ 21"......aiming for 50#@26" you have very little wood to remove. You do need to get the inner 1/3 working some more though. I'd be aiming for 45# finished with a good tiller. The string angle thing is why I wouldn't use reflexed handle designs anymore on a wooden bow, I use steam to straighten any natural handle reflex.
Logged
Pages: [1]
« previous next »