Author Topic: Bamboo Backed Lemonwood  (Read 3181 times)

0 Members and 1 Guest are viewing this topic.

Offline Maxspin

  • Member
  • Posts: 83
Bamboo Backed Lemonwood
« on: July 08, 2013, 12:02:40 pm »
I got my trade bow past the long line and braced over the weekend. Would like some input before I go any farther. Running out of time to screw this up…….

I would say that it is bending too much at the fades. I would start working about mid limb, but would like to get input from the experts.

At rest.


Long Line


Braced


Pulled to 15"


Keith

Offline Joec123able

  • Member
  • Posts: 1,769
Re: Bamboo Backed Lemonwood
« Reply #1 on: July 08, 2013, 01:10:11 pm »
Yea to much bend in the fades
I like osage

Offline toomanyknots

  • Member
  • Posts: 3,132
Re: Bamboo Backed Lemonwood
« Reply #2 on: July 08, 2013, 02:02:44 pm »
My advice would be to slow down the bending and drawing until you get that fade to chill out and not bend like that. Remove wood from the entire limb except near the fade that is bending. Remember to never draw the bow farther than it takes to identify a problem/part you need to work on, like a hinge, or a flat spot. Go slow and work the limb a bit after every time you remove material to make sure the adjustment is worked in, per say.
"The way of heaven is like the bending of a bow-
 the upper part is pressed down,
 the lower part is raised up,
 the part that has too much is reduced,
 the part that has too little is increased."

- Tao Te Ching, 77, A new translation by Victor H. Mair

Offline bubby

  • Member
  • Posts: 11,054
Re: Bamboo Backed Lemonwood
« Reply #3 on: July 08, 2013, 03:51:25 pm »
there is always time to screw one up >:D, sorry, on these r/d bows I really basically only work mid limb out till I get the outers to open up some and work back to the fades, I don't build a lot of these but that is how I attack them, jmo for what it's worth
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline vinemaplebows

  • Member
  • Posts: 1,419
Re: Bamboo Backed Lemonwood
« Reply #4 on: July 08, 2013, 03:52:23 pm »
Yep, too much bend at the fades....hows it going Keith? :) What Bubby said.....
Debating is an intellectual exchange of differing views...with no winners.

Offline rossfactor

  • Member
  • Posts: 805
  • Humboldt County CA
Re: Bamboo Backed Lemonwood
« Reply #5 on: July 08, 2013, 05:13:55 pm »
I don't think this is screwed up.  Just start removing wood mid limb and out, till the tiller starts to become more even.  In my limited experience (with R/Ds) the mid limb removal can start to show up later in the draw, so its easy to over do it.  Go slow, check the tiller a lot, and pull a bit farther just when things start to even out between inner and mid limbs.

Gabe
Humboldt County CA.

mikekeswick

  • Guest
Re: Bamboo Backed Lemonwood
« Reply #6 on: July 09, 2013, 04:58:21 am »
It's really only the left fade that is bending too much. Exercise it plenty.

Offline bushboy

  • Member
  • Posts: 2,256
Re: Bamboo Backed Lemonwood
« Reply #7 on: July 09, 2013, 11:27:33 am »
Like already stated,outer and mids gotta move.exercise between scrapes till your ready to fall over,then exercise it some more! R/D like to give a false tiller if not worked a lot.
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline Maxspin

  • Member
  • Posts: 83
Re: Bamboo Backed Lemonwood
« Reply #8 on: July 16, 2013, 10:42:21 am »
Been working on this a little every day.
here is the progress I have made.
July 11




July 15




I can still see a hing at the Left fade, and am concerned about making weight at this point.  >:(

Offline Will H

  • Member
  • Posts: 2,120
Re: Bamboo Backed Lemonwood
« Reply #9 on: July 16, 2013, 10:50:17 am »
Looks like it's gonna be a sweet bow! BTW I sent you a PM ;) check your inbox :)
Proud Member of Twin Oaks Bowhunters
           Clarksville, Tennessee

   "Middle Tennessee is the place to be"

Offline Maxspin

  • Member
  • Posts: 83
Re: Bamboo Backed Lemonwood
« Reply #10 on: July 30, 2013, 12:08:12 pm »
Thanks to everyone who chimed in on this. I got it worked out. Just getting the finishing touches done. Then will get it shipped out.  :)

Offline toomanyknots

  • Member
  • Posts: 3,132
Re: Bamboo Backed Lemonwood
« Reply #11 on: July 30, 2013, 01:09:54 pm »
It's really only the left fade that is bending too much. Exercise it plenty.

I second that, watch that fade. That's a very likely spot to have a failure.
"The way of heaven is like the bending of a bow-
 the upper part is pressed down,
 the lower part is raised up,
 the part that has too much is reduced,
 the part that has too little is increased."

- Tao Te Ching, 77, A new translation by Victor H. Mair

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,911
  • Eddie Parker
Re: Bamboo Backed Lemonwood
« Reply #12 on: July 30, 2013, 10:58:11 pm »
The tiller looks good for a reflex/deflex, now I would start taking it off from mid limb on out. I lot of people start scraping everytime from the fade and don't realize until it's too late that you can't put the scraper in the same spot over and over.
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline Maxspin

  • Member
  • Posts: 83
Re: Bamboo Backed Lemonwood
« Reply #13 on: July 31, 2013, 11:13:32 am »
I just didn’t see it in the long line. The reflex/deflex is new for me. Had an Oh Crap moment when I put the shorter string on it.  Need to get some more pictures taken. I am shooting it out now and putting on the finishing touches.

Keith

Offline Maxspin

  • Member
  • Posts: 83
Re: Bamboo Backed Lemonwood
« Reply #14 on: August 12, 2013, 10:58:00 am »
I finished it  ;D









Shipped on Friday  ;D

Keith