« previous next »
Pages: [1] 2

Author Topic: draw length on sinew backed bow  (Read 8715 times)

0 Members and 2 Guests are viewing this topic.

Offline sadiejane

  • Member
  • Posts: 1,030
draw length on sinew backed bow
« on: October 27, 2011, 12:43:51 pm »
sinew backed a nice little piece of osage back in the spring.
pulled it outta the rafters where it's been curing since then.
getting tiller about dialed in.
got to wondering just what sorta draw length i can get outta this bow.
it's 50" ntn(and right now about 60lbs-way more than i can pull past about 12"  :D).
was originally thinking it would need to be shorter(25" or less)
but wondered with the sinew backing if i can take it further?
it's fine with me if it ends up being a shorter draw bow, just thinking.
thanks
Logged
wild women don't get the blues

Offline Keenan

  • Member
  • Posts: 4,824
Re: draw length on sinew backed bow
« Reply #1 on: October 27, 2011, 12:53:08 pm »
If it's a bend through the handle, then you should be able to make about 25"
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: draw length on sinew backed bow
« Reply #2 on: October 27, 2011, 01:43:19 pm »
You should be able to get another inch or maybe 2" ith the sinew backing and like Keenan if it bends through the handle.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline JW_Halverson

  • Member
  • Posts: 11,923
Re: draw length on sinew backed bow
« Reply #3 on: October 27, 2011, 03:03:27 pm »
For stiff handled-short fadeout flatbows out of osage I double the draw length to determine the nock-to-nock length.  For example: I shoot a 26" draw length that might stretch to 27 if I cheat a little on form. 

I have a sinew and snake backed osage that is 52".  That bow has 4 inches of handle and a total of 3 inches of fadeouts, leaving me with 22" of working limb on the bottom and 23" on the top. 

I'd figure a little shorter if it's bendy in the handle, but the shorter you go the worse the string angle on the nocks.  Recurving the tips will help with that, but if you have already sinewed, recurving the tips is kinda out of the question.   I wouldn't fear pulling that bow you got to the 26" mark, personally. 

Post a pic or three, I'd like to see it!
Logged
Guns have triggers. Bicycles have wheels. Trees and bows have wooden limbs.

Offline sadiejane

  • Member
  • Posts: 1,030
Re: draw length on sinew backed bow
« Reply #4 on: October 27, 2011, 05:31:01 pm »



first let me say i made some rookie mistakes with this bow.
didnt take it down near far enough before sinewing.
didnt ruin the bow but didnt allow the most benefit from the sinew.
this was after my second bow early spring late winter.
had this stick that was thin and buggy and was hankering to sinew a bow.
certainly have learned lots from it already.
and look forward to the next candidate for sinew.

and it is far from complete but getting there.
in the top photo the right limb is the top.
you might notice the lower(left) limb has a tad of natural reflex at the tip.
its at 18" on the tiller stick
i can pull it right about 20" now so a guess of about 45" @ 20" at present.

what ya'll think to this point?
thanks!
Logged
wild women don't get the blues

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: draw length on sinew backed bow
« Reply #5 on: October 27, 2011, 06:16:24 pm »
Get those outter limbs bending more. That will give you a few more inches to play with.  Also on a short bow like this it is a good idea to flip the tips a bit to improve the string angle at full draw.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline sadiejane

  • Member
  • Posts: 1,030
Re: draw length on sinew backed bow
« Reply #6 on: October 27, 2011, 08:29:52 pm »

took some wood from the outer limbs as pat so wisely suggested. still needs a bit more removed me thinks. took it to the woodlot and put about 20 arrows thru it. shoots with some authority and as accurate as i am.... still only able to pull to about 22". reckon when i thin down those ends a tad more it will pull to 24" and i think i'll call that good. at least till its had a few hundred arrows thru it.
thanks pat!
Logged
wild women don't get the blues

Offline Keenan

  • Member
  • Posts: 4,824
Re: draw length on sinew backed bow
« Reply #7 on: October 27, 2011, 09:42:32 pm »
 Looking great! Nice tiller.  The more I shoot the short sinew bows the more I love them.
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: draw length on sinew backed bow
« Reply #8 on: October 27, 2011, 09:46:44 pm »
That did make a big difference.  8)  You are reaching 90deg with the string/tip angle. It will start stacking soon. How close is the sinew to the tips? Does it stop short of the tips or go all the way to them. The reason I'm asking...if you could kick the tips up a bit you could get another few inches maybe...but it would take heat to do it. 
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,911
  • Eddie Parker
Re: draw length on sinew backed bow
« Reply #9 on: October 27, 2011, 10:59:05 pm »
 If you had flipped those tips a little so the string didn't pull off you could have got 28" easy. I've done it with shorter ones than 50". You could always peel the sinew back a little and heat bend the tips then reaply the sinew all the way and over the tips.
Logged
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline PatM

  • Member
  • Posts: 6,737
Re: draw length on sinew backed bow
« Reply #10 on: October 28, 2011, 12:53:04 am »
Splicing in some extensions ia a quick and easy way of stretching the bow and draw a bit.
Logged

Offline sadiejane

  • Member
  • Posts: 1,030
Re: draw length on sinew backed bow
« Reply #11 on: October 28, 2011, 12:07:39 pm »
yes, the sinew comes down over the tips about 4-5".
and yes, after i had the sinew on and curing for awhile, realized i prolly outta have flipped those tips.
as i said, rookie mistakes. but i am learning.
and the next one will be done differently.

meantime, since im not gonna remove sinew, or add extensions, i do have one more question.
had thought to wrap some sinew around towards tip to cover where end of sinew comes to on belly and to insure sinew holds over time.
when i do that, how long do i need to let that sinew cure before shooting bow again?
thanks folks, really appreciate your comments and suggestions.
Logged
wild women don't get the blues

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: draw length on sinew backed bow
« Reply #12 on: October 28, 2011, 12:14:56 pm »
I always wrap the termination of the sinew with sinew then cover that with decorative silk thread. You want to do this after final sanding so you don't hurt the sinew wrap. The wrap shouldn't need more than a few days to dry before sealing and shooting.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline ErictheViking

  • Member
  • Posts: 1,504
Re: draw length on sinew backed bow
« Reply #13 on: October 28, 2011, 01:47:41 pm »
Very cool bow Sadie.
Logged
"He that but looketh on a plate of ham and eggs to lust after it hath already committed breakfast with it in his heart"  C.S. Lewis

Offline sadiejane

  • Member
  • Posts: 1,030
Re: draw length on sinew backed bow
« Reply #14 on: October 28, 2011, 02:46:24 pm »
Quote from: Pat B on October 28, 2011, 12:14:56 pm
I always wrap the termination of the sinew with sinew then cover that with decorative silk thread. You want to do this after final sanding so you don't hurt the sinew wrap. The wrap shouldn't need more than a few days to dry before sealing and shooting.

thanks pat-was hoping i wouldnt have to wait for months or weeks...
Logged
wild women don't get the blues
Pages: [1] 2
« previous next »