« previous next »
Pages: [1]

Author Topic: Paring Ladder (shave horse ladder)  (Read 3158 times)

0 Members and 1 Guest are viewing this topic.

Offline gfugal

  • Member
  • Posts: 746
Paring Ladder (shave horse ladder)
« on: August 17, 2018, 08:57:42 am »
https://youtu.be/4a-qev2J8T0

For those who don't have a bench vise, a shave horse, a workshop table and shave pony, or whatever, this may be an option for your draw knives. I ran across it today on Youtube. I had never heard of it before.
Logged
Greg,
No risk, no gain. Expand the mold and try new things.

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Paring Ladder (shave horse ladder)
« Reply #1 on: August 17, 2018, 08:59:47 am »
Simple but effective!   :OK
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Hawkdancer

  • Member
  • Posts: 5,040
Re: Paring Ladder (shave horse ladder)
« Reply #2 on: August 17, 2018, 10:33:08 am »
A neat way to clean up staves, or make kindling!  I think I would want a leather apron working a draw knife that way, though.  Not sure why he worked the rungs that way, though.  A good,  taut lashing jog should be sufficient, unless it is to hold the notch better.
Hawkdancer
Logged
Life is far too serious to be taken that way!
Jerry

Offline gfugal

  • Member
  • Posts: 746
Re: Paring Ladder (shave horse ladder)
« Reply #3 on: August 18, 2018, 11:11:25 pm »
Logged
Greg,
No risk, no gain. Expand the mold and try new things.

Offline gfugal

  • Member
  • Posts: 746
Re: Paring Ladder (shave horse ladder)
« Reply #4 on: August 18, 2018, 11:26:07 pm »
But I do eventually make a shave horse (nothing quite compares) I probably will go with a compact design like this.

https://youtu.be/9o8rX0DCm-4
Logged
Greg,
No risk, no gain. Expand the mold and try new things.

Offline khperkins

  • Member
  • Posts: 18
Re: Paring Ladder (shave horse ladder)
« Reply #5 on: August 19, 2018, 05:42:11 am »
Some great ideas.
Logged

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Paring Ladder (shave horse ladder)
« Reply #6 on: August 19, 2018, 07:11:30 am »
I have stripped a lot of bark and sapwood off osage by putting one end of the stave at the base of a tree and the other end on my chest, I would lean forward and go to work with a draw knife. This was green wood right off the stump and cut very easily. I was also much younger and osage cutting crazy at the time.
Logged

Offline gfugal

  • Member
  • Posts: 746
Re: Paring Ladder (shave horse ladder)
« Reply #7 on: August 19, 2018, 11:48:33 am »
Quote from: Eric Krewson on August 19, 2018, 07:11:30 am
I have stripped a lot of bark and sapwood off osage by putting one end of the stave at the base of a tree and the other end on my chest, I would lean forward and go to work with a draw knife. This was green wood right off the stump and cut very easily. I was also much younger and osage cutting crazy at the time.

Interesting! Wouldn't that hurt your chest? When I debark staves I just lean it up against the wall or a fork in the tree, and kneel as I pull down, taking of strips of bark off that way. But this method doesn't allow you to get the very tips as you can't pull down past the ground.
Logged
Greg,
No risk, no gain. Expand the mold and try new things.

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Paring Ladder (shave horse ladder)
« Reply #8 on: August 20, 2018, 07:11:10 am »
I put a pad on my chest and do the very ends later in a vise.

This was not ring chasing precision work, this was hogging off sapwood and bark quickly when I had a lot of osage to process and get sealed with shellac. I did this draw knifing in the woods next to my yard.   I chose this place because I didn't have to clean up the mountains of bark and shavings I produced like I would had I done the same work in my shop.
Logged
Pages: [1]
« previous next »