« previous next »
Pages: [1]

Author Topic: what would you do?  (Read 1646 times)

0 Members and 1 Guest are viewing this topic.

Offline jeffp51

  • Member
  • Posts: 1,641
what would you do?
« on: July 19, 2015, 10:42:28 pm »
I have an osage belly split -- 64 inches long but just 1.25" wide mid limb.  It is also a bit narrower on the belly than the back, which means I may not have all that width. no knots. What do you think I can get out of it?  What profile would you go for?
Logged

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: what would you do?
« Reply #1 on: July 19, 2015, 10:47:25 pm »
See what happens. I'd leave it full width until a little past mid limb narrowing to 3/8 inch nocks.

I made a bow from an osage sucker years ago and got 49# out of it. It had about 3 inches of reflex. It was 1 inch wide.

I made an osage  bow for my daughter (2005) that was about 3/4" wide. I finished it at 25# at 22 inches. I reflexed the last 8 inches.

It doesn't take much wood to make an osage bow.

Jawge
Logged
Set Happens!
If you ain't breakin' you ain't makin!

Offline huisme

  • Member
  • Posts: 1,036
  • I'm Marc, but not that Marc.
Re: what would you do?
« Reply #2 on: July 19, 2015, 10:52:50 pm »
+1, narrow bodied reflex/deflex bows are fun :)
Logged
50#@26"
Black locust. Black locust everywhere.
Mollegabets all day long.
Might as well make them short, save some wood to keep warm.

Offline crooketarrow

  • Member
  • Posts: 2,790
Re: what would you do?
« Reply #3 on: July 19, 2015, 11:13:40 pm »
  I mainly made stiff handle bow with the limbs (ELB)1 1/8" to 1 1/4" wide at the fades right off the handle. This will make bows fro 50 to 65 # bows.

  But have made osage bows down to 3/4" good many around 1".  Osage bows around a inch will come out good around 40 to 45 pounds.

  Did just finish a Iroqous long bow 58" 50# @ 26. Did
nt take any picks sorry on it's way MD
Logged
DEAD IS DEAD NO MATTER HOW FAST YOUR ARROW GETS THERE
20 YEARS OF DOING 20 YEARS OF LEARNING 20 YEARS OF TEACHING

Offline chamookman

  • Member
  • Posts: 3,027
Re: what would you do?
« Reply #4 on: July 20, 2015, 05:22:43 am »
Without seeing it, I's venture to say 50lbs should be possible  ! Bob
Logged
"May the Gods give Us the strength to draw the string to the cheek, the arrow to the barb and loose the flying shaft, so long as life may last." Saxon Pope - 1923.

Offline sleek

  • Member
  • Posts: 6,764
Re: what would you do?
« Reply #5 on: July 20, 2015, 08:17:56 am »
I just built one at mojam with those dimensions, except mine is shorter. Its 53@26. Its deflex handle, mildly reflexed tips. Bow shoots amazing wih no measurable set.
Logged
Tread softly and carry a bent stick.

Dont seek your happiness through the approval of others

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,637
Re: what would you do?
« Reply #6 on: July 20, 2015, 08:24:21 am »
Sometimes with wood bows you don't get to do a specific design. You just have to start reducing wood so you get both limbs bending evenly and together. Find the handle area get the limbs shaped as closely as possible and get the tiller right.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

blackhawk

  • Guest
Re: what would you do?
« Reply #7 on: July 20, 2015, 08:40:28 am »
You can do most any "normal" design with that...depends on what you wanna make.....I'm finishing up a 64.5" ntn stiff handled osage just over 1 1/8" wide at the fades,and pulls 40@28" right now....I'm sure it could've taken more weight but the person requested 40@28". 
Logged
Pages: [1]
« previous next »