Author Topic: Utah (Vernon hills) Wonderstone  (Read 5753 times)

0 Members and 1 Guest are viewing this topic.

Offline JoJoDapyro

  • Member
  • Posts: 2,504
  • Subscription Number PM109294
Utah (Vernon hills) Wonderstone
« on: June 11, 2015, 11:04:51 pm »
I'm still pounding away on this stuff. A little better spalling thanks to some hours watching Jack Crafty. This was all done with a quartz 1 pound hammer stone. I'll see if I can get some flaking done on it tomorrow.
If you always do what you always did you'll always get what you always got.
27 inch draw, right handed. Bow building and Knapping.

Offline Redhand

  • Member
  • Posts: 704
  • Marlen Murdock PM109458
Re: Utah (Vernon hills) Wonderstone
« Reply #1 on: June 12, 2015, 12:49:58 pm »
That is cool looking stone.  Did you go out and collect it yourself?
Northern Ute

Offline JackCrafty

  • Global Moderator
  • Member
  • Posts: 5,628
  • Sorry Officer, I was just gathering "materials".
Re: Utah (Vernon hills) Wonderstone
« Reply #2 on: June 12, 2015, 12:53:22 pm »
Wonderstone is TOUGH... so I've heard.  I never tried it.  That looks like good hammerstone work.  :)  I tend to snap workpieces when they get thin and I'm smacking away with a hammerstone.
Any critter tastes good with enough butter on it.

Patrick Blank
Midland, Texas
Youtube: JackCrafty, Allergic Hobbit, Patrick Blank

Where's Rock? Public Waterways, Road Cuts, Landscape Supply, Knap-Ins.
How to Cook It?  200° for 24hrs then 275° to 500° for 4hrs (depending on type), Cool for 12hr

Offline JoJoDapyro

  • Member
  • Posts: 2,504
  • Subscription Number PM109294
Re: Utah (Vernon hills) Wonderstone
« Reply #3 on: June 12, 2015, 05:03:26 pm »
I did collect it myself. As well as heat treat it. It is very hard. Very Very Hard.
If you always do what you always did you'll always get what you always got.
27 inch draw, right handed. Bow building and Knapping.

Offline Redhand

  • Member
  • Posts: 704
  • Marlen Murdock PM109458
Re: Utah (Vernon hills) Wonderstone
« Reply #4 on: June 12, 2015, 10:33:43 pm »
Vernon hills isn't that by Tooele. That's about a 3 hour drive for me. I would like to try knapping some of that stone.
Northern Ute

Offline JoJoDapyro

  • Member
  • Posts: 2,504
  • Subscription Number PM109294
Re: Utah (Vernon hills) Wonderstone
« Reply #5 on: June 13, 2015, 02:52:28 pm »
It is Redhand. From Tooele drive south to Vernon. Pass through the town (stop at the silver spur for a bite to eat) keep going south until you get the the railroad (about 4 miles) turn left. The dirt road is a monster if its wet. You can see the pit from down the hill a bit. It is about 2 miles from the highway to the pit. Someone takes a front end loader and digs it out, so it is scattered all over the ground. Some is very coarse, and hasn't been good for knapping. I just took my rock hammer and broke a corner off chunks until I found good chunks. Also, it doesn't flake very well, it is very very tough. Mine has been heat treated at 680 degrees for 12 hours. I'm am going to try another batch at a higher temp to see if that improves the flaking. If you don't have access to a kiln, let me know. I can make another run and get some heat treated and if you come out I can trade heat treated for raw. Let me know. I'm in Sandy.
If you always do what you always did you'll always get what you always got.
27 inch draw, right handed. Bow building and Knapping.

Offline bubby

  • Member
  • Posts: 11,054
Re: Utah (Vernon hills) Wonderstone
« Reply #6 on: June 13, 2015, 04:19:15 pm »
Jo try the same heat for 24 hrs
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline JoJoDapyro

  • Member
  • Posts: 2,504
  • Subscription Number PM109294
Re: Utah (Vernon hills) Wonderstone
« Reply #7 on: June 13, 2015, 08:53:58 pm »
Can I reheat the same stone?
If you always do what you always did you'll always get what you always got.
27 inch draw, right handed. Bow building and Knapping.

Offline Trapper Rob

  • Member
  • Posts: 3,719
Re: Utah (Vernon hills) Wonderstone
« Reply #8 on: June 13, 2015, 10:20:00 pm »
JoJo you can put it back in the kiln.

Offline JoJoDapyro

  • Member
  • Posts: 2,504
  • Subscription Number PM109294
Re: Utah (Vernon hills) Wonderstone
« Reply #9 on: June 13, 2015, 10:34:45 pm »
Awesome. I'll go fire it up here in a few.
If you always do what you always did you'll always get what you always got.
27 inch draw, right handed. Bow building and Knapping.

Offline caveman2533

  • Member
  • Posts: 640
  • Steve Nissly
Re: Utah (Vernon hills) Wonderstone
« Reply #10 on: June 14, 2015, 10:00:54 am »
This look like the same place?



« Last Edit: June 14, 2015, 10:03:58 am by caveman2533 »

Offline Redhand

  • Member
  • Posts: 704
  • Marlen Murdock PM109458
Re: Utah (Vernon hills) Wonderstone
« Reply #11 on: June 14, 2015, 11:32:14 am »
That would be great thank you
Northern Ute

Offline JoJoDapyro

  • Member
  • Posts: 2,504
  • Subscription Number PM109294
Re: Utah (Vernon hills) Wonderstone
« Reply #12 on: June 14, 2015, 07:58:10 pm »
Yes Sir. Looks dang near the same. I'll get on my PC and upload a photo I took.
« Last Edit: June 14, 2015, 08:02:42 pm by JoJoDapyro »
If you always do what you always did you'll always get what you always got.
27 inch draw, right handed. Bow building and Knapping.

Offline Ghost Knapper

  • Member
  • Posts: 181
Re: Utah (Vernon hills) Wonderstone
« Reply #13 on: June 18, 2015, 10:18:53 pm »
Does anyone have any finished points made out of this stuff? I believe I have some but not 100% sure, had it given to me a time or two ago and just stumbled upon it again.

Offline Majuba Tom

  • Member
  • Posts: 275
Re: Utah (Vernon hills) Wonderstone
« Reply #14 on: June 18, 2015, 10:56:49 pm »
Here is one from Nevada wounder stone I made.