« previous next »
Pages: [1]

Author Topic: What brass for 3/8" dowels?  (Read 3802 times)

0 Members and 1 Guest are viewing this topic.

Offline Stonedog

  • Member
  • Posts: 257
What brass for 3/8" dowels?
« on: December 18, 2013, 08:46:27 pm »
I have some 3/8" dowels I want to make into small game "flying log" arrows...

Will any caliber brass fit over a 3/8" dowel?
Logged
Till shade is gone, till water is gone, into the Shadow with teeth bared, screaming defiance with the last breath, to spit in Sightblinder's eye on the Last Day.

-Aiel Saying

Offline Dharma

  • Member
  • Posts: 453
  • Kayenta, AZ
Re: What brass for 3/8" dowels?
« Reply #1 on: December 18, 2013, 09:18:35 pm »
.38 Special or .357 Magnum
Logged
An arrow knows only the life its maker breathes into it...

Grasshopper Mouse

  • Guest
Re: What brass for 3/8" dowels?
« Reply #2 on: December 18, 2013, 11:04:37 pm »
Or...
Make it into a nutter.
Taper the tip per a regular glue-on point and screw on a 3/8" nut. A drop of epoxy or other glue will help it hold on.
They hit hard and they're super easy and cheap.

Guy
Logged

Offline Thesquirrelslinger

  • Member
  • Posts: 1,245
Re: What brass for 3/8" dowels?
« Reply #3 on: December 18, 2013, 11:13:18 pm »
9mil will fit decently well, or some hot glue and a 9mil.
plus, if you have friends that shoot a lot, they are cheap.
Logged
"Insanity is doing the same thing over and over again and expecting different results"

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: What brass for 3/8" dowels?
« Reply #4 on: December 18, 2013, 11:44:56 pm »
I agree with Guy. A nutter is deadly on small game with the shock of the hex nut and a little penetration from the tapered point...and cheap.  ;)
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Stonedog

  • Member
  • Posts: 257
Re: What brass for 3/8" dowels?
« Reply #5 on: December 19, 2013, 09:42:45 am »
Anyone have any idea how many hex nuts I would need to equal 300 grains?  These are actually for my medieval bolt shooting device that shoots 16" OAL bolts  ;D...with that short of "arrow" I need them to be FOC heavy to achieve the penetration needed for clean kills.

I already play on shooting 300 grain broad heads!


The idea of nutters with a homemade bleeder blade sounds DEADLY!
Logged
Till shade is gone, till water is gone, into the Shadow with teeth bared, screaming defiance with the last breath, to spit in Sightblinder's eye on the Last Day.

-Aiel Saying

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,911
  • Eddie Parker
Re: What brass for 3/8" dowels?
« Reply #6 on: December 19, 2013, 10:34:39 pm »
Uh, weigh them. ???
Logged
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline Stonedog

  • Member
  • Posts: 257
Re: What brass for 3/8" dowels?
« Reply #7 on: December 20, 2013, 09:25:38 am »
'Ah have nae grain scale laddie!
Logged
Till shade is gone, till water is gone, into the Shadow with teeth bared, screaming defiance with the last breath, to spit in Sightblinder's eye on the Last Day.

-Aiel Saying

Offline CORIUS

  • Member
  • Posts: 158
Re: What brass for 3/8" dowels?
« Reply #8 on: December 20, 2013, 07:50:07 pm »
.762mm will fit if u cut off the neck
Logged
Where there's a will, there's a bow.


PA subscription #: PM108452

Offline Thesquirrelslinger

  • Member
  • Posts: 1,245
Re: What brass for 3/8" dowels?
« Reply #9 on: December 20, 2013, 10:14:55 pm »
7.62 :)
Any of the .30 cal will fit very well.
7.62 base, and the part that holds the powder is rather large- about 1 cm in diam...
7.92 works good.
Recently, I have been cutting off the necks of .223 and/or 5.56(almost identical).
Its near perfect fit. Literally. And the longer brass adds wieght, allows me to add some lead, and also keeps the shaft from breaking right after the point.
If you cut off the base of the cartridge(primer, etc), and then slit the neck, it makes a cheap and easy ferrule.
44 mag work really good on Ceder arrows.
They add some weight...
Logged
"Insanity is doing the same thing over and over again and expecting different results"

Offline scattershot

  • Member
  • Posts: 161
Re: What brass for 3/8" dowels?
« Reply #10 on: December 22, 2013, 06:22:11 pm »
I use two 3/8" nuts for my nutters, they weigh 160 grains for both.
Logged
"Experience is just a series of non-fatal mistakes"
Pages: [1]
« previous next »