« previous next »
Pages: [1] 2

Author Topic: Trouble Finishing Bow Limbs  (Read 3977 times)

0 Members and 1 Guest are viewing this topic.

Offline Nashoba

  • Member
  • Posts: 31
Trouble Finishing Bow Limbs
« on: November 20, 2012, 10:35:02 pm »
Hey guys.
I am currently working on a hickory flatbow for my girlfriends little sister. I have the grip shaped out and the limb tips are about where I want them. The problem I am having is with the mid limbs, specifically the six inches directly above the grip. The limbs in that section are far thicker than the tips, and when I try using a hand plane to remove material I end up pulling material off all the way to the tips. I cannot find a way to thin the area down without messing up either the grip or the limb tips. Any ideas on techniques or tools to deal with this?
My tool kit consists of a drawknife, a hand plane, a sanding block, a rasp plane, a few different files, and assorted knives.
Thanks!
Logged

Offline bow101

  • Member
  • Posts: 2,235
Re: Trouble Finishing Bow Limbs
« Reply #1 on: November 20, 2012, 11:45:29 pm »
Hello Nashoba, I have 2 planes that I use. One is set up for aggresive wood removal and I have a smaller hand plane that is adjusted for thin shavings. I have yet to have the privleage of working with hickory. Most of my wood consists of Eastern maple, red & white oak. When I plane oak with the hand plane it just takes off a very fine sliver, You can actually see through it.
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline steve b.

  • Member
  • Posts: 999
Re: Trouble Finishing Bow Limbs
« Reply #2 on: November 20, 2012, 11:51:18 pm »
I've never used a hand plane on a bow.  For belly work I either use scrapers or rasps.  For the area you described I use a rasp with course and fine (r) sides.  The rough side removes wood quickly and leaves deep grooves in the wood.  I flip the rasp and use the fine side to get those grooves out.  Then I grab a scraper and smooth it out even more.  It would take less than five minutes to make a considerable change in that area.
« Last Edit: November 21, 2012, 12:14:00 am by steve b. »
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Trouble Finishing Bow Limbs
« Reply #3 on: November 21, 2012, 12:02:16 am »
I do the same as steve b.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Weylin

  • Member
  • Posts: 2,296
Re: Trouble Finishing Bow Limbs
« Reply #4 on: November 21, 2012, 12:11:07 am »
I agree, that sounds like the perfect job for a rasp.
Logged

Offline Fred Arnold

  • Member
  • Posts: 1,566
  • From up on Munson Creek
Re: Trouble Finishing Bow Limbs
« Reply #5 on: November 21, 2012, 12:25:28 am »
x2 for the rasp. At the point you are at I get rid of the knives and planes, time for finesse work with rasps, files, and scrapers.
Logged
I found many years ago that it is much easier and more rewarding working with those that don't know anything than those that know it all.

Offline Carson (CMB)

  • Member
  • Posts: 2,319
Re: Trouble Finishing Bow Limbs
« Reply #6 on: November 21, 2012, 12:25:48 am »
Like Steve B. said. 
Logged
"The bow is the old first lyre,
the mono chord, the initial rune of fine art
The humanities grew out from archery as a flower from a seed
No sooner did the soft, sweet note of the bow-string charm the ear of genius than music was born, and from music came poetry and painting and..." Maurice Thompso

Offline soy

  • Member
  • Posts: 2,897
  • pm106221
Re: Trouble Finishing Bow Limbs
« Reply #7 on: November 21, 2012, 03:21:15 am »
I'm working on a hickory right now And just like you're describing you need to use that rasp... and if you don't have a cabinet scraper you need to pick 1 up there cheap and handy and well worth their weight in gold ...imho
Logged
Is this bow making a sickness? or the cure...

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 32,204
  • if you have to ask you wouldn't understand ,Tenn.
Re: Trouble Finishing Bow Limbs
« Reply #8 on: November 21, 2012, 07:28:05 am »
Rasp and scraper,never used a planer on a bow before. :)
   Pappy
Logged
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: Trouble Finishing Bow Limbs
« Reply #9 on: November 21, 2012, 07:33:17 am »
Rasp and scraper.  Once you become familiar with a dknife's use you could use it too. Jawge
Logged
Set Happens!
If you ain't breakin' you ain't makin!

Offline Buckeye Guy

  • Member
  • Posts: 3,033
Re: Trouble Finishing Bow Limbs
« Reply #10 on: November 21, 2012, 04:22:30 pm »
For Hickory I use 50 or 80 grit sandpaper save your rasp for the Osage !
Have fun !
Guy
Logged
Guy Dasher
The Marshall Primitive Archery Rendezvous
Primitive Archery Society
Having  fun
To God be the glory !

Offline bow101

  • Member
  • Posts: 2,235
Re: Trouble Finishing Bow Limbs
« Reply #11 on: November 21, 2012, 04:30:42 pm »

I need another rasp, the one I have is to aggresive it leaves very rough gouges in the wood. I also use 50-60 grit paper on a finishing sander. Having arthritic hands doesn't help matters.
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline Onebowonder

  • Member
  • Posts: 1,495
Re: Trouble Finishing Bow Limbs
« Reply #12 on: November 21, 2012, 04:38:42 pm »
I love my Shinto Rasp for this sort of work.  It gives you great control of the wood removal process.  Follow with a scapper once you get down close to where you want to be.

OneBow
Logged

Offline SLIMBOB

  • Member
  • Posts: 3,759
  • Deplorable Slim
Re: Trouble Finishing Bow Limbs
« Reply #13 on: November 21, 2012, 05:43:30 pm »
Old school.  Draw knife and sand paper.
Logged
Liberty, In God We Trust, E Pluribus Unum.  Distinctly American Values.

Offline Gordon

  • Member
  • Posts: 3,299
Re: Trouble Finishing Bow Limbs
« Reply #14 on: November 21, 2012, 09:22:26 pm »
A spoke shave works well if you don't have too many knots or grain swirls.
Logged
Gordon
Pages: [1] 2
« previous next »