« previous next »
Pages: [1] 2

Author Topic: Red Oak Recurve Sneak Peek  (Read 10976 times)

0 Members and 1 Guest are viewing this topic.

Offline Josh

  • Member
  • Posts: 3,367
  • Silence is golden but duct tape is silver.
Red Oak Recurve Sneak Peek
« on: February 21, 2011, 11:01:21 pm »
This is all I got so far.  Gonna put the finish on it and then post it.  Just really proud of this one so far had to show the tips off.  :)
Logged
“The trouble with quotes on the Internet is you never know if they are genuine.” —Abraham Lincoln

Offline n2huntn

  • Member
  • Posts: 468
  • jeff_smith13@hotmail.com ROLL TIDE !
Re: Red Oak Recurve Sneak Peek
« Reply #1 on: February 21, 2011, 11:04:33 pm »
Tease!
Logged
Genesis 27: 3

Offline Matt S.

  • Member
  • Posts: 380
Re: Red Oak Recurve Sneak Peek
« Reply #2 on: February 21, 2011, 11:07:24 pm »
Was this from a board or a stave? Steam, boil or direct heat?
That's a nice recurve tip, I hope I can make some like that in the future!
Logged

Offline sailordad

  • Member
  • Posts: 5,045
Re: Red Oak Recurve Sneak Peek
« Reply #3 on: February 21, 2011, 11:09:02 pm »
Josh, thats a nice looking curve
cant wait to see the rest of her
Logged
i always wanted a harley,untill it became the "thing to ride"
i ride because i love to,not to be part of the crowd

Offline Josh

  • Member
  • Posts: 3,367
  • Silence is golden but duct tape is silver.
Re: Red Oak Recurve Sneak Peek
« Reply #4 on: February 21, 2011, 11:10:34 pm »
Thanks guys.  It is from a board and I steamed the wood for around 45 minutes before I bent them.  I bent the limbs over a year ago finally decided to splice them together this weekend and finish it up.  Almost done with it now.  ;D ;D
Logged
“The trouble with quotes on the Internet is you never know if they are genuine.” —Abraham Lincoln

Offline ken75

  • Member
  • Posts: 1,886
  • crepe myrtle is my "yella wood"
Re: Red Oak Recurve Sneak Peek
« Reply #5 on: February 21, 2011, 11:29:08 pm »
lookin good ...i blew a recurve up today , hope this one comes out better than mine
Logged

Offline Matt S.

  • Member
  • Posts: 380
Re: Red Oak Recurve Sneak Peek
« Reply #6 on: February 21, 2011, 11:34:20 pm »
Quote from: Josh on February 21, 2011, 11:10:34 pm
Thanks guys.  It is from a board and I steamed the wood for around 45 minutes before I bent them.  I bent the limbs over a year ago finally decided to splice them together this weekend and finish it up.  Almost done with it now.  ;D ;D

I hope I don't annoy you with my questions, but did you bend it when it was 3/4" thick (assuming this came from a 1x board) or did you thin the board down to near finished thickness? I do most of my work with RO board bows and I'm just starting to experiment with bending, so to see how successful you've been with this gives me lots of encouragement!
Can't wait to see the finished bow.
Logged

Offline Josh

  • Member
  • Posts: 3,367
  • Silence is golden but duct tape is silver.
Re: Red Oak Recurve Sneak Peek
« Reply #7 on: February 21, 2011, 11:54:13 pm »
That sucks Ken keeping my fingers crossed with mine!  ;)


Matt, I think I took the tips down to half an inch thick before I steamed them.  Then I used a piece of tin on the belly while bending to keep splinters to a minimum but it still had a few.  they came out while tillering.  I didn't use a 1x2 it was actually a 1x4 and I cut the board to 2" wide.  The finished bow is around 1 7/8ths wide at the fades.  Hope this helps.  :)  Good luck with yours!
Logged
“The trouble with quotes on the Internet is you never know if they are genuine.” —Abraham Lincoln

Offline Matt S.

  • Member
  • Posts: 380
Re: Red Oak Recurve Sneak Peek
« Reply #8 on: February 22, 2011, 12:00:00 am »
Quote from: Josh on February 21, 2011, 11:54:13 pm
That sucks Ken keeping my fingers crossed with mine!  ;)


Matt, I think I took the tips down to half an inch thick before I steamed them.  Then I used a piece of tin on the belly while bending to keep splinters to a minimum but it still had a few.  they came out while tillering.  I didn't use a 1x2 it was actually a 1x4 and I cut the board to 2" wide.  The finished bow is around 1 7/8ths wide at the fades.  Hope this helps.  :)  Good luck with yours!

Yes, that helps a lot. Thanks! :)
Logged

Offline eagleone

  • Member
  • Posts: 13
Re: Red Oak Recurve Sneak Peek
« Reply #9 on: February 22, 2011, 01:24:08 am »
that is sweet! cant wait to see more pics
Logged

Offline NTD

  • Member
  • Posts: 1,771
Re: Red Oak Recurve Sneak Peek
« Reply #10 on: February 22, 2011, 01:32:24 am »
Looking good Josh!
Logged
Nate Danforth

Offline aero86

  • Member
  • Posts: 1,263
Re: Red Oak Recurve Sneak Peek
« Reply #11 on: February 22, 2011, 01:58:06 am »
man, you got me thinking about building another asian style bow out of red oak
Logged
profsaffel  "clogs like the devil" I always figured Lucifer to be more of a disco kind of guy.

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Red Oak Recurve Sneak Peek
« Reply #12 on: February 22, 2011, 02:04:08 am »
Nice looking curves Josh. Looking forward to seeing the rest.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Dauntless

  • Member
  • Posts: 282
Re: Red Oak Recurve Sneak Peek
« Reply #13 on: February 22, 2011, 02:25:59 am »
Those are some serious recurves!  Come to think of it, I have a very plain red oak d bow that could be spruced up...
Logged
The starving grad student with too many hobbies.

Offline Timo

  • Member
  • Posts: 2,026
Re: Red Oak Recurve Sneak Peek
« Reply #14 on: February 22, 2011, 10:12:07 am »
Whats up with these "sneak peeks" kinda like taken a tea break? ??? Come on Bring it already! ;)
Logged
Pages: [1] 2
« previous next »