« previous next »
Pages: [1]

Author Topic: what is too thin for maple,  (Read 1970 times)

0 Members and 2 Guests are viewing this topic.

Offline Kitsu

  • Member
  • Posts: 198
  • Räven bakom masken
what is too thin for maple,
« on: November 13, 2010, 03:38:09 pm »
when making any bow out of maple, what is the thinnest the bow can go before it breaks,

i am aiming for about 50lbs
the bow is 51" N2N

was wondering because most bows i have made were longer, and i do not want to risk this breaking,
 thanks,

i will upload pics as to what i have at this moment,  i will get them asap
Logged
"If you open your mind for me
You won't rely on open eyes to see
The walls you build within come tumbling down
And a new world will begin" ----- Queensryche, "Silent Lucidity

R.H , Southeastern PA/Western PA.

Offline Marc St Louis

  • Administrator
  • Member
  • Posts: 7,877
  • Keep it flexible
    • Marc's Bows and Arrows
Re: what is too thin for maple,
« Reply #1 on: November 13, 2010, 04:06:40 pm »
Thin is not an issue
Logged
Home of heat-treating, Corbeil, On.  Canada

Marc@Ironwoodbowyer.com

Offline Kitsu

  • Member
  • Posts: 198
  • Räven bakom masken
Re: what is too thin for maple,
« Reply #2 on: November 13, 2010, 04:45:05 pm »
Quote from: Marc St Louis on November 13, 2010, 04:06:40 pm
Thin is not an issue


alright, thanks then, should be finished soon then
Logged
"If you open your mind for me
You won't rely on open eyes to see
The walls you build within come tumbling down
And a new world will begin" ----- Queensryche, "Silent Lucidity

R.H , Southeastern PA/Western PA.

Offline Kitsu

  • Member
  • Posts: 198
  • Räven bakom masken
Re: what is too thin for maple,
« Reply #3 on: November 13, 2010, 11:45:56 pm »
i was sanding a limb finishing it up, and i slipped, not fully slipping to break the limb completely but enough to cause it to be ruined, it was 55lbs at 24 inches, very good for a shortbow in my opinion, and was the best i had made, i am heartbroken but i gotta keep going and fight through it, i already started on another one, but its not even roughed out yet, and even then it will take a while to dry, but, wish me luck, i am going to need it.

it has a slight twist to it, and since i do not have access to any heat treating eq, i plan on roughing it out and lashing two boards to it, in an attempt to fix the twist,  since it  is not  fully dry i hope it dries straight(er),

btw, the slipping was caused by sawdust on my shoe, and the smooth floor, but before i sanded it i got a few shots out of it, was an amazing shooter, thats what depressed me, the feeling of success, and then the feeling of failure, due to something STUPID... if it was the woods fault i would have been fine... but it wasnt...

sorry for the dissapointment, i know you people would have loved to see the finished product, and you will see one, just as soon as i can finish another up,   ill even try to aim for something better :P...

Logged
"If you open your mind for me
You won't rely on open eyes to see
The walls you build within come tumbling down
And a new world will begin" ----- Queensryche, "Silent Lucidity

R.H , Southeastern PA/Western PA.

Offline gstoneberg

  • Member
  • Posts: 3,889
Re: what is too thin for maple,
« Reply #4 on: November 14, 2010, 10:06:14 am »
Bummer, but way to get right back after it.  We'll look forward to the next one...and the next... ;D

George
Logged
St Paul, TX

Offline sailordad

  • Member
  • Posts: 5,045
Re: what is too thin for maple,
« Reply #5 on: November 14, 2010, 10:29:48 am »
sorry to hear that,good luck on the next one  :)

as far as this next one goes,with the twist
if it isnt to severe i wouldnt even worry about
i have made several bows that have had some degree of twist to them,no problems they shoot fine

but clamping them to a board,once its roughed out,to dry is the right way to go
good luck
Logged
i always wanted a harley,untill it became the "thing to ride"
i ride because i love to,not to be part of the crowd
Pages: [1]
« previous next »