Primitive Archer

Main Discussion Area => Bows => Topic started by: Sticks on January 22, 2019, 11:58:18 am

Title: D bow question
Post by: Sticks on January 22, 2019, 11:58:18 am

I was wondering what are the advantages of a Cherokee style D bow other than ease of build and nostalgia.Im thinking about a build but have only built rigid handle bows so far,any opinions are appreciated.

Title: Re: D bow question
Post by: ksnow on January 22, 2019, 12:02:31 pm

You can get away with a shorter stave since there is no nonworking length (handle). Given the same length stave, a d bow will be under less tress at a given draw length.

And, they look really primitive.

Have fun with one.

Kyle

Title: Re: D bow question
Post by: bradsmith2010 on January 22, 2019, 12:06:32 pm

they shoot really well,,

Title: Re: D bow question
Post by: Sticks on January 22, 2019, 12:18:30 pm

Thanks for the replys I have a 25 inch draw and am looking for 50 pounds out of a white oak stave would 62 NTN be a good starting point.

Title: Re: D bow question
Post by: bradsmith2010 on January 22, 2019, 12:20:07 pm

Yes

Title: Re: D bow question
Post by: Bayou Ben on January 22, 2019, 12:58:32 pm

I agree with what was said above.  I also like how light they are in the hand and how easy they are to carry.

Title: Re: D bow question
Post by: Badger on January 22, 2019, 01:14:46 pm

  As said above, under a lot less stress, they tend to take less set and are very efficient shooters.

Title: Re: D bow question
Post by: Sticks on January 22, 2019, 02:39:31 pm

Im thinking 5/8 at the tips and 7/8 mid grip that sound like a plan or should I start out heavier

Title: Re: D bow question
Post by: bradsmith2010 on January 22, 2019, 03:07:43 pm

1 1/4  or 1 1/2,, and narrow if needed as you tiller,, better to start out with some wiggle room,,

Title: Re: D bow question
Post by: Sticks on January 22, 2019, 04:03:16 pm

I should have been more specific above I was thinking 1 1/4 grip width 3/4 wide at the tips 5/8 thick at the tips and 7/8 thick at the grip thanks so much for the directions its appreciated add anything if you like.this would be the rough out.

Title: Re: D bow question
Post by: bradsmith2010 on January 23, 2019, 11:48:29 am

leave the limbs wide and parallel ...1 1/2,,, narrow the tips as needed,,

Title: Re: D bow question
Post by: burchett.donald on January 25, 2019, 05:26:24 am

Sticks,
          When I started with bendy's /D bows I found that proper tiller was a little more complicated than a stiff/non bending handle...Getting the proper circle and balance was a task...Luckily I had "half eye" to guide me...I found quickly that it was a different experience...I think you will enjoy the journey...The center comes into play moving at just full draw, which is tedious work unlike a rigid handle...Proper balance was really technical and touchy...Have fun and please keep us posted...When built correctly they are very efficient performers...Fun to carry also
                                                                                                                           Don
                                                                                                                                                                             

Title: Re: D bow question
Post by: George Tsoukalas on January 25, 2019, 06:16:53 am

i enjoy making them from red oak boards. Thay are a little easier to tiller and seem to shoot really well and take less set. Jawge