Primitive Archer
Main Discussion Area => Bows => Topic started by: bowmo on February 26, 2007, 04:05:39 pm
-
Just about done with this one. Bamboo back with an osage core that has a thin redheart stripe in it and a bamboo belly. Redheart underlays and sheep hoof, red heart, and yew tip overlays. Yew and redheart handle. The bamboo back is covered with rattlesnake skins. 64" long, 56# at 28". Made this one for a guy who posts over on another site. Almost going to be hard to send this one off. A darn good bow.
Dan
[attachment deleted by admin]
-
:)
[attachment deleted by admin]
-
that's really beautiful and well done. I have always wanted to do one of those.
Davce
-
That is pretty. Does the boo taper away at the fades? How about at the tips were the redheart starts. Justin
-
Thanks!
If you look you can see that the bamboo on the belly tapers into nothing in the fades. At the tips I belt sanded through the bamboo and into the osage a bit before I glued on the redheart, so it laps over the last 1" of the bamboo and onto the osage core.
dan
-
Holy COW! What a good lookin' bow! How well does she shoot?
-
That is what it looked like, I just wanted to make sure. Is the boo at the fades tapered from the inside (belly) and the outside (back) of the piece? Did you pre-tiller each piece? Justin
-
Another one to purrrty to take into the woods Great! Ridge
-
Dan, that is a great looking bow.
-
My, my your bows just keep getting better and better. That one's some real eye candy!
-
Thanks!
She shoots great...sweet in the hand and packs a real wallop!
The bamboo is tapered from the outside of the piece in the fades...it cuts through the power fibers but it's in a non bending area so it doesn't matter... Ya, I definitely pre tiller each piece. I just held them in my hand and flexed them though...
dan
-
Beautiful as always bowmo.
-
Thanks! :)
-
that is quite a peace of work,...an all other level there :), great attention to details
-
Absolutely gorgeous. Such nice lines. How about sharing with us a photo at full draw? -OldBow
-
Now that is a beauty! Sweet job with that one. Maybe you should tell the guy that it broke and give him something a little less stunning! Hang that baby on your wall!(LOL)
-
Yep got to be hard to part with that one - - she's a beauty.
-
...
[attachment deleted by admin]
-
That is a pretty bow Dan, but I would suggest gettin the mid and outer limbs working more if you can, its bending awefully hard right off the fades. Maybe just try tapering the core a bit more on the next one, I know its hard to tiller one with raw boo on the belly. ;)
-
I agree whith Ryano. Anyways that's a real treat for the eye ;)
Btw what glue did you use, and did you use steam or dry heat to bend the pieces into that form?
-
Ya, I would have been more annoyed with the way it turned out if it hadn't shot so darn nice! But, anyway you guys have seen my work...you know I prefer a more elliptical tiller...your not telling me anything I don't know. Bamboo belly's are certainly a real challenge! But I always learn a lot as I go...you'll see another one of these from me soon, as the belly of that yew tri lam I recently made is starting to degrade in a most unusual way!? Yew sucks! So, I decided to try and save it by adding a bamboo belly...we'll see how that goes...
I use a mix of smooth on epoxy and tite bond 3...smooth on for the splices and any full length limb lamination's...tite bond 3 for the power lams, handle lams, tip overlays and underlays.
You don't use heat at all....the reflex and the deflex are forced into those shapes while gluing and held in by the glue line.
Dan
-
You sure about letting that bow loose. Super! Ridge
-
The bow had a lot of deflex, so I don't know if its bending overly hard there or not. It'd be interesting to see the braced pic superimposed on the full draw. Torges' R/D design had some pretty straight looking limbs at full draw so I don't know that it is necessary to get this design to be nicely round. In fact, a rounded full-draw measn the reflexed area is under more stress than the rest of the bow. Of course that is part of why R/D works so well, only slightly moving mass on inner limbs and fairly stiff outer limbs, leaving the poor mid-limbs to do all the work.
-
Outstanding! 'Nuf said :P
Looking forward to seeing it this weekend for March Backed Bow of the Month
Thanks for the FULL DRAW PIC ;)
-
Very nice, that's a sweet looking bow.
Sean
-
Yew sucks!
That's the first time I've seen those two words side-by-side! :D
-
Nice looking bow. From the color of the bamboo on the belly it doesn't look like you tempered it. By tempering the belly boo you will incease the compression and strengthen the limb so you can cut down on limb mass. I agree with the other guys that it looks like the limbs aren't working very much from mid limb out. Try spreading your flex over more of the limb and tempering the belly and I bet you will be pleased with the results. Pat
-
O.K. now, that's just way too nice! :-) Great Job!
-
Hi dan,
saw you Boo bow on the threat, is the belly wood made from Raw Boo? how about the back of the bow, Raw Boo as well with snake skin glue on?
Pls send your reply to robt188@yahoo.com
God Bless, RT
-
Great bow :o. I love the wood combo. I like the full draw profile. If you got those limbs bending in a nice arc you would loose a ton of performance. I have made a bow that had a similar profile and my neighbor made one at the same time. We made our bows to the same dimentions as each other and glued on the same form ect. The only difference was tiller. His was tillered to a nice arc mine looked straight. No comparison in performance. The straighter looking one shoots a full 50 yds. further with the same arrow. Just my experience I am no expert. :)
Jesse