« previous next »
Pages: 1 2 [3] 4 5 ... 7

Author Topic: Making a Snake (finished pics on pg 5)  (Read 20697 times)

0 Members and 1 Guest are viewing this topic.

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #30 on: November 20, 2018, 06:39:46 pm »
Then I grabbed the heat gun and began the alignment/ side-profile adjustment process, which may take a little while.
That's all for now folks!
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline Taxus brevifolia

  • Member
  • Posts: 304
Re: Making a Snake
« Reply #31 on: November 21, 2018, 12:43:42 am »
Wow this is wonderful, thanks very much for sharing. Simply amazing
Logged

Offline gfugal

  • Member
  • Posts: 746
Re: Making a Snake
« Reply #32 on: November 21, 2018, 10:23:59 am »
The nice thing about your build alongs is you work so fast that you don't leave us hanging.
Logged
Greg,
No risk, no gain. Expand the mold and try new things.

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #33 on: November 21, 2018, 06:11:40 pm »
Quote from: gfugal on November 21, 2018, 10:23:59 am
The nice thing about your build alongs is you work so fast that you don't leave us hanging.

Lol.  ;D

Well here I go again  :D

Got the alignment/ side profile set with the heat gun...
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #34 on: November 21, 2018, 06:14:30 pm »
Then I floor tillered to a low brace. As I started to bend her a little I noticed the outers (one in particular) needed some work.
« Last Edit: November 21, 2018, 06:18:36 pm by upstatenybowyer »
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline bradsmith2010

  • Member
  • Posts: 5,187
Re: Making a Snake
« Reply #35 on: November 21, 2018, 06:15:49 pm »
lookin good..when can we shoot it,, (-P
Logged

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #36 on: November 21, 2018, 06:16:30 pm »
I continued tillering and got her to a pretty nice bend, pulling my target 55# @ about 23"
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #37 on: November 21, 2018, 06:19:19 pm »
Not done posting yet Brad!  ;D
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #38 on: November 21, 2018, 06:20:24 pm »
I had to see it bending in the hand so I took a few pics of that...
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #39 on: November 21, 2018, 06:28:41 pm »
Okay, so everything's going good, but now I've gotta tell ya'll about an issue I knew I'd have to address sooner or later. There's a pretty significant weathering check that starts about 10" from the tip and runs almost all the way.  :(

But have no fear!  :D I've got a solution.  8)

Cutting across it is unavoidable, so I do so, fill with epoxy (and a little CA where the check is too thin to get any epoxy in there) and clamp her up.

Once it's cured I'll wrap with sinew where the check runs off the limb (might be overkill but better safe then sorry).

And that's it for now. Happy Thanksgiving everyone!  :G :G :G -C- -C- -C- )P( )P( )P(
« Last Edit: November 21, 2018, 06:31:51 pm by upstatenybowyer »
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline rps3

  • Member
  • Posts: 1,514
Re: Making a Snake
« Reply #40 on: November 22, 2018, 06:30:58 am »
Following along. Looking good, hope that check doesnt give you any problems.
Logged

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: Making a Snake
« Reply #41 on: November 22, 2018, 08:34:16 am »
Coming along nicely Jeff. Enjoying the build. Happy Thanksgiving.
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #42 on: November 22, 2018, 07:17:30 pm »
Thanks Bj. Happy Thanksgiving to you and your family.  :)
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: Making a Snake
« Reply #43 on: November 23, 2018, 06:55:21 am »
That is looking great. Did you cut the splice with a saber saw? Jawge
Logged
Set Happens!
If you ain't breakin' you ain't makin!

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: Making a Snake
« Reply #44 on: November 23, 2018, 06:25:31 pm »
Thanks Jawge. I actually used the bandsaw. Saber saw is a great idea though. Maybe I'll try that next time.  :OK

Well I got around to cleaning up that checked area and wrapping with sinew. I gave it 3 wraps going back to where the check starts. 
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb
Pages: 1 2 [3] 4 5 ... 7
« previous next »