« previous next »
Pages: 1 [2] 3

Author Topic: Glueing a handle on a stave  (Read 6037 times)

0 Members and 1 Guest are viewing this topic.

Offline mspink

  • Member
  • Posts: 213
Re: Glueing a handle on a stave
« Reply #15 on: January 02, 2017, 08:50:19 pm »
TB 3 is good and very water resistant.
Logged
Aim small miss small!

Offline PatM

  • Member
  • Posts: 6,737
Re: Glueing a handle on a stave
« Reply #16 on: January 02, 2017, 10:33:54 pm »
You need to use a glue with no creep for an application like that.
Logged

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: Glueing a handle on a stave
« Reply #17 on: January 03, 2017, 07:26:11 am »
Pat I'm sorry but I'm kinda dumb when it comes to glues. I'm not sure what "no creep" means. I'm guessing that it's something not absorbed by the wood. I might have to look up some of the glue post
I've read but not really paid enough attention to.
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline bubby

  • Member
  • Posts: 11,054
Re: Glueing a handle on a stave
« Reply #18 on: January 03, 2017, 09:09:48 am »
The tight bond glues have a little creep or slide action but if you do like Erick said with the lams or use strips of leather you should be ok . this is one reason i went to a bow epoxy
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: Glueing a handle on a stave
« Reply #19 on: January 03, 2017, 10:23:09 am »
Thanks Bubby don't imagine you can buy that glue at hardware store? Probably best bet would be 3r?
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline bubby

  • Member
  • Posts: 11,054
Re: Glueing a handle on a stave
« Reply #20 on: January 03, 2017, 11:08:03 am »
Bj i use smooth on get it from 3 rivers or the factory. There is a urea based that u can get at the hardware store but i can't remember the name right now i know u just add water like unibond maybe someone will chime in with the name i know patb knows what it is maybe pm him
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline bubby

  • Member
  • Posts: 11,054
Re: Glueing a handle on a stave
« Reply #21 on: January 03, 2017, 11:22:35 am »
It's dap weldwood plastic resin glue
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: Glueing a handle on a stave
« Reply #22 on: January 03, 2017, 11:25:32 am »
Thanks Bubby, thanks everyone. Funny how something that seems so easy can get kinda complicated
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: Glueing a handle on a stave
« Reply #23 on: January 04, 2017, 09:31:40 am »
Well I got this one tillered to where I have to start working close to the fades and it needed handle for that. I took Eric's advice and cut 3 narrow strips, 2 black walnut and 1 Mulberry. After fileing and scrapping everything as flat as I could get it I glued it up with TB2.  I roughed out the fades handle still needs shaping but I think this will work. Thanks for the help everyone
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline bubby

  • Member
  • Posts: 11,054
Re: Glueing a handle on a stave
« Reply #24 on: January 04, 2017, 10:20:03 am »
👍👍
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Josh B

  • Member
  • Posts: 3,741
Re: Glueing a handle on a stave
« Reply #25 on: January 04, 2017, 11:35:24 am »
You're fade angle is still a bit too steep/abrupt.  You'll have better luck with a flatter transition from riser block to limb.  Josh
Logged

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: Glueing a handle on a stave
« Reply #26 on: January 11, 2017, 10:27:13 pm »
I finished up this handle I really like how it turned out. It is 7/8" wide where arrow contacts
handle.It shoots the same spine arrows right or left hand and my friend likes how it fits his hand. Original plan was to wrap handle but it shoots nice off knuckles and he likes how it looks naked. I put one more thin piece of cedar on. Thanks again for all the help
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline chamookman

  • Member
  • Posts: 3,026
Re: Glueing a handle on a stave
« Reply #27 on: January 12, 2017, 05:07:07 am »
Looks good BJ ! Bob
Logged
"May the Gods give Us the strength to draw the string to the cheek, the arrow to the barb and loose the flying shaft, so long as life may last." Saxon Pope - 1923.

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: Glueing a handle on a stave
« Reply #28 on: January 12, 2017, 07:02:29 am »
Thanks Bob, I've always put arrow shelfs in my handles but I've been shooting left handed a lot lately. I made a left hand handle with arrow shelf for my son and now this ambidextrous handle. I'm actually getting pretty comfortable shooting left handed and like the shoot opportunities it could provide.
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline bubby

  • Member
  • Posts: 11,054
Re: Glueing a handle on a stave
« Reply #29 on: January 12, 2017, 09:02:46 am »
Looks good bj i think you have it figured out
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹
Pages: 1 [2] 3
« previous next »