« previous next »
Pages: [1]

Author Topic: new red oak bow  (Read 2210 times)

0 Members and 1 Guest are viewing this topic.

Offline mikebarg

  • Member
  • Posts: 54
new red oak bow
« on: October 31, 2016, 04:49:49 pm »
I've been working on this one for the past 4 weeks(when I have time). It's a red oak board. 64 inches NTN. 1" wide at the handle. Limbs are 1.5" wide . Then taper to 5/8" in the last 12". It's pulling 45# @ 25". I would like to lighten it up just a little more.
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,637
Re: new red oak bow
« Reply #1 on: October 31, 2016, 05:10:00 pm »
Your tiller looks good. All you should have to do to reduce weight is 5 full length scrapes on each limb and check weight. If not enough do 5 more. Exercise after each wood removal.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline bubby

  • Member
  • Posts: 11,054
Re: new red oak bow
« Reply #2 on: October 31, 2016, 05:13:02 pm »
Yup do as pat says, looks good. How much have you shot it, it will lose a few #'s when it gets a few hundred arrows through it
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline mikebarg

  • Member
  • Posts: 54
Re: new red oak bow
« Reply #3 on: October 31, 2016, 05:18:12 pm »
I've only put 50 - 60 arrows through it so far.
Logged

Offline JW_Halverson

  • Member
  • Posts: 11,925
Re: new red oak bow
« Reply #4 on: October 31, 2016, 05:46:05 pm »
Make sure you have rounded over the corners on the edges of the limbs, too.  That helps prevent most of the limb failures on board bows!

Looks like this one is gonna be a shooter for ya!
Logged
Guns have triggers. Bicycles have wheels. Trees and bows have wooden limbs.

Offline mikebarg

  • Member
  • Posts: 54
Re: new red oak bow
« Reply #5 on: November 04, 2016, 12:56:10 pm »
I put a very light coat of stain on the bow.
Logged

Offline loon

  • Member
  • Posts: 1,307
Re: new red oak bow
« Reply #6 on: November 04, 2016, 02:19:47 pm »
Nice
Logged

mikekeswick

  • Guest
Re: new red oak bow
« Reply #7 on: November 04, 2016, 02:51:06 pm »
The right limb is bending a bit too much in the inner third. Your left limb shows a better elliptical tiller, see how it is a bit stiffer in that inner third, that is correct when you have parallel inner limbs. Maybe there is a small thin spot almost at the tip of the left limb too? Check the thickness here to make sure it is even with no dips.
Also round your edges on the back over quite a bit more. You want them somewhere around the radius of a pea :)
Logged

Offline selfbow joe

  • Member
  • Posts: 996
  • 1-812-344-1590
Re: new red oak bow
« Reply #8 on: November 04, 2016, 06:46:53 pm »
Nice looking bow
Logged

Offline DesertDisciple

  • Member
  • Posts: 151
  • Arise, for it is your task, and we are with you
Re: new red oak bow
« Reply #9 on: November 05, 2016, 03:26:42 am »
Nice! Loving that bend. How's it shoot?
Logged
Best Regards,

Andrew

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: new red oak bow
« Reply #10 on: November 05, 2016, 10:03:56 am »
Tiller is good. Watch that handle to fade transition. Looks a bit angular and abrupt. Jawge
Logged
Set Happens!
If you ain't breakin' you ain't makin!
Pages: [1]
« previous next »