« previous next »
Pages: [1]

Author Topic: Fixable ?  (Read 2318 times)

0 Members and 1 Guest are viewing this topic.

Offline Joec123able

  • Member
  • Posts: 1,769
Fixable ?
« on: January 15, 2014, 11:24:32 pm »
So about a month and a half ago I steamed this handle to try and align the tips when I clamped it down it half cracked in a weird way I then just through it on the floor and then left it til now. Now does it look fixable ? Hopefully because this thing has a ton of character It would seem obvious that I could just clamp it down but the handle has a lot of checks in it



Logged
I like osage

Offline Zion

  • Member
  • Posts: 783
  • The blacksmith's mare walks barefoot
Re: Fixable ?
« Reply #1 on: January 15, 2014, 11:28:29 pm »
You could pop that off and glue on a new riser
Logged
The secret of life is learning to make your own luck.

Offline Bryce

  • Global Moderator
  • Member
  • Posts: 3,125
  • Pacific Ghost Longbows
Re: Fixable ?
« Reply #2 on: January 15, 2014, 11:35:11 pm »
pour some glue down in there and clamp it up.
Logged
Clatskanie, Oregon

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Fixable ?
« Reply #3 on: January 15, 2014, 11:50:17 pm »
How thick is the limb between the crack and the back of the stave?
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Joec123able

  • Member
  • Posts: 1,769
Re: Fixable ?
« Reply #4 on: January 15, 2014, 11:55:00 pm »
Well it's basically impossible to clamp I cannot for the life of me get it clamped since the crack is right in the fade area it won't clamp with the odd angle so I guess the only option is pop it off
Logged
I like osage

Offline Blaflair2

  • Member
  • Posts: 2,042
Re: Fixable ?
« Reply #5 on: January 16, 2014, 02:53:49 am »
Did the same thing yesturday! I popped it and glued on a different piece. U need to make sure u have an island to glue the block on.
Logged
Nothing ventured nothing gained

Offline bubby

  • Member
  • Posts: 11,054
Re: Fixable ?
« Reply #6 on: January 16, 2014, 03:20:28 am »
Get an innertube run some glue in it and wrap it up snug
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline simson

  • Member
  • Posts: 2,310
  • stonehill-primitive-bows
    • stonehill-primitive-bows
Re: Fixable ?
« Reply #7 on: January 16, 2014, 05:50:37 am »
I would warm (notheat) it up, let run in some epoxi (gets fluid when warm), clamp in vice and wait 24 hours.
that should make the job.
Logged
Simon
Bavaria, Germany

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 32,204
  • if you have to ask you wouldn't understand ,Tenn.
Re: Fixable ?
« Reply #8 on: January 16, 2014, 06:44:21 am »
Super glue and clamp in a vice is what I would do, it is on the compression side so shouldn't be a problem.  :)
 Pappy
Logged
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Fixable ?
« Reply #9 on: January 16, 2014, 10:47:35 am »
That is pretty bad, I wouldn't trust it and suspect it will delaminate even with glue in the crack.

I made an errant cut with my band saw on a really fine osage stave a while back, put the stave back for years then decided to fix it.

I only had 1/2" thickness of handle area to work with so I glued on 1/8" strips to start. Once I got the handle up to about  3/4" in thickness I glued on a thicker piece to complete the new handle depth. I used Urac for glue.

You have to feather these strips into the limbs to keep them from popping off.

 

I made this bow in 2008, it is still shooting with no handle problems.
« Last Edit: January 16, 2014, 10:50:43 am by Eric Krewson »
Logged
Pages: [1]
« previous next »